7 DIY Practice’s to Clean up Minor Dents away from Car at Home ( Along Few Tactics )

Here we brought up 7 DIY quick and easy methods for several minor dents to get them out at home 
that makes you happy when you notice your car.

As we know, it is impossible to defend a car from getting road dirt, debris, bird’s shits, scratches, and dents while driving it on the naked road.

If you are a competent driver and get success in saving your car or a truck during driving,

But you never defend your vehicle from getting dents in a parking lot, in stuck traffic, or even in a marketplace.

After getting dents, some standard approaches like paint, body shop, and parts replacement occur for factory look again.

Before getting into these practices, more quick and easy solutions are available, and you can do it yourself.

Here we brought up 7 DIY quick and easy methods for several minor dents to get them out at home that makes you happy when you notice your car.

1. How to clean up dents with the help of “Plunger or Suction cup “

Using a plunger practice to get car dents out.

The first helpful solution to get car dents out is by using a quick and easy plunger practice.

A plunger is an everyday tool used to unclog drains, but it isn’t used for removing blockages, Also very useful for getting minor to medium-sized round dents out of your car.

But make sure to use a cup plunger instead of a regular toilet or flange plungers,

Because a cup plunger produces the suction that is ideal for using to get car dents out.

Before pulling the dent, You first need to pour hot water over the plunger and dented surface for a good seal.

After pouring hot water, place the plunger against the dent and pull it back a few times until the dent pops out ( With a pop-out sound ).

This practice performs great on flat-body panels, doors, side panels, plastic parts ( bumpers ). That forms a depression and does not damage the car’s paint.

If the plunger is not performing and cannot get suction, it is either due to vacuum leakage, not using enough water,

Working with the wrong kind of plunger, and using this method on large dent surfaces.

Tip

If the plunger doesn’t get suction and perform well, it is due to vacuum leakage or insufficient water.

Caution

Applying this technique on large dented surfaces or using the wrong plunger-type can’t deliver the expected output.

2. How to clean up dents with the help of “Boiling Water”

Using a boiling water method to get car bumper dents out.

This method only works great for plastic parts like bumpers and allows you to reach behind to push the dent.

But it is still challenging to take off the bumper to push out the dent from behind due to its hardness.

Boiling water is the best way to tackle this situation. Because it softens the hard plastic surface and allows you to push the dent out.

The only things required to do boil some water and then pour the hot water over the dent,

And reach behind the bumper by wearing gloves to protect your hands and push behind to push out the ding.

If it is difficult to reach behind the bumper, then remove it from the car and do the procedure.

Once the dent removal procedure is complete, pour cold water to reset the plastic and let it cool for 3-5 minutes.

The aim of pouring hot water over the hard plastic is to make it flexible, making it easy to pop it back into place.

So, don’t limit yourself to boiling water in the kitchen for cooking and washing purposes

Get more valuable benefits like removing dents from bumpers.

Caution

This method doesn’t perform well on metal surfaces, and it will damage the paintwork.

3. How to clean up minor dents with the help of “Hammer & Dolly”

Using a Hammer & Dolly method to get car trunk dents out.

This practice works for medium to large dents and a dent that does not respond to any other process.

To do this practice, you need a rubber mallet or a body hammer, and a curved piece of metal or a dolly used to shape sheet metal.

The selection of the hammer and dolly is always based on the size, shape, and location of the dent. 

If bigger the dent size, the bigger the hammer and dolly size you need.

This process requires a rubber mallet hammer, not a typical building hammer. Make sure before adopting this method.

Using this practice for getting the dings out requires placing the dolly on top of the dent first, And then using the rubber mallet from the inside against the dolly. 

After that, first start hammering from the deepest point of the dent, or the center, and then work your way through the dent. 

This hammering method only works when the dent can be accessed from the rear side of the panel and to reshape the car’s exterior.

If you want to practice this mallet and a dolly method to clean up the rid dent on your car, Make sure to first wrap the hammer’s head in a towel to cut the impact

Before hammering, tap the dent with the hammer and keep tapping until the dings pop themselves out.

Tip

Warp the hammer with a cloth before jumping into this practice

Catution

This practice requires more attention and can crush your fingers.

4. How to clean up dents with the help of “Hair dryer & Compressed air”

Using a Hair dryer & Compressed air practice to get car bumpers dents out.

The combo of a hairdryer and compressed air is the most popular practice, which is quick, effortless to pop out dents.

Hairdryer expands the plastic by heating the car dent direct with it, And the compressed air contracts the plastic by spraying due to its coldness will help pop the dent out.

The first thing is to turn the hairdryer to its hottest setting and direct the air toward the dent to expand the car’s plastic. 

When the car plastic is warm to the touch, without delay, take the cane of compressed air, flip it upside down, and start spraying the heated area.

Since the rapid changes in the temperature allow the dent to pop out on its own, making this process easy and quick.

If you don’t get satisfied with the plunger method, try to remove dents from car plastic by using this method.

Caution

There is a chance that heating too much can damage the body’s paintwork.

5. How to clean up minor dents with the help of “Dry ice”

Using a piece of dry ice to get car trunk dents out.

Usually, dry ice is used as a cooling agent, but it can also be used for getting minor dents out of the car.

The only thing you need to do, wear protective gloves and hold a piece of dry ice

And start rubbing the dent around until you hear the pop-out sound or the dent pop back into its original place.

This practice can also act the same by combining a piece of dry ice instead of compressed air with a hairdryer to pull the dented surface back.

Expanding and contracting a combo will allow the car’s plastic to pop out to its original position.

This practice is easy and quick but only suitable for minor dents and requires no extra things. Only needs a pair of protective gloves and a piece of dry ice.

Using dry ice for minor dents is more efficient than other practices, but it is not ideal to use large dents.

6. How to clean up minor dents with the help of “Vacuum cleaner & Bucket or Pot”

Using a Vacuum cleaner & Bucket practice to get car dents out.

Such a practice needs suction to pull out, which is considered safe and reliable.

But to create the suction, you need a plunger with low suction power for minor dents that need a little effort.

If you need more power to pull outdent, then you need a dent puller with the right amount of power, but that costs you more.

The best solution is to create your own by using household products like a vacuum cleaner and a bucket or pot. 

After grasping things together, you need to make a small hole underneath the pot or a bucket

Tape the pot around the dent and then place the vacuum cleaner hose over the hole under the pot. After that, turn your vacuum on. 

If the dent under the pot is not too shallow, then the suction can pull a dent out back into place.

This practice is a little bit complex, but it works well, and as we know that the suction can pop out dents.

7. How to clean up dents with the help of “Dent Removal Kits”

Using a Dent Removal Kit to get car dents out.

Wrapping our list with the fast, reliable, and properly instructional solution.

A dent removal kit is designed to fix car dents and comes with special equipment for repair and pulling purposes.

If you have little experience repairing dents, then this mentioned practice works excellent for you. 

These kits are available on the market with a variety of tools to repair car dents. 

Some kits come with suitable tools for minor dents, while others have tools for taking care of large dents

If you have no experience, In that case, using tools that come with proper instructions will be the best solution for you.

Caution

Make sure the product you are going to buy is compatible with your car dents.

Frequently Ask Question about getting dent out of a car

What is the best practice to clean up a car bumper’s dent?

The combo of boiling water and plunger or suction cup is the easy and quick solution for this practice.

You only need to pour hot water over the plunger and dented surface for a good seal because a suction cup produces the suction, 

That is ideal for getting minor to medium-sized round dents out of your car.

Is it possible to get a dent out of a car with the help of tape?

In some cases, dents (e.g. dents without damaging paintwork like pushed or pressed ) on car doors and other flat panels. 

It can be brought back into its original form by applying the tape correctly and pulling the dent back with the help of tape.

How to clean up minor dents from the car trunk?

There are a few practices used to clean up minor dents from the car trunk. 

The first one is with the help of dry ice. The only thing you need to do, wear protective gloves and hold a piece of dry ice, and start rubbing the dent around until you hear the pop-out sound.

The second way is Hammer & Dolly. Using this practice for getting the dings out requires placing the dolly on top of the dent first, and then using the rubber mallet from the inside against the dolly. 

The third way is using dent removal kits. It is designed to fix car dents and comes with special equipment for repair and pulling purposes.

The only thing you need is to have little experience repairing dents, then this practice works excellent for you.

How to pull a dent out of a car fender?

The first one is quick and easy practice using a plunger or suction cup method. And it is very useful for getting minor to medium-sized round dents out of your car.

The second way is a hairdryer & compressed air. The combo of a hairdryer and compressed air is the most popular practice, which is quick, effortless to pop out dents.

The third way is using dent removal kits. It is designed to fix car dents and comes with special equipment for repair and pulling purposes. 

The only thing you need is to have little experience repairing dents, then this practice works excellent for you.

Conclusion

All the methods mentioned above are suitable for a person who has little experience with dealings with dents or dings that reduce the risk of more mess.

A person having no experience will damage the surface if not handled the methods described above properly.

In that case, an especially designed kit with proper instruction is the best choice to go or can even try the methods containing low risk, 

Like plunger method, hairdryer and compressed air, dry ice in the case of small dents with proper precautions.

About the author

David Johnson

Add comment

Recent Posts

Recent Comments